|
1. |
|
NEW 40' x 14' x 4' Self Propelled Spud Barges On Order
|
Custom Build
|
2024
|
Self Propelled Spud Barge
|
40'
|
|
|
These 40x14x4 Raked Bow Sectional Barges include the following features: 5/16" plate, 3x3x1/4 framing on 20" spacing, 6 cleats, flush manways, 4x6 angle connecting rails with 1.25" pins, 2 coat Safety Red anticorrosive exterior epoxy paint and antifouling on the underwater hull. (2) 12" spudwells for 10" spuds, all 30ft long with hats and pins included.
|
2. |
|
New 124' Inland Steel Steel Barge For Sale
|
|
Custom Modified 2024
|
Inland Spud Barge
|
124'
|
|
|
Custom built, finished in 2024 and USCG Registered. Ready to go.
|
3. |
|
50' Self Propelled Spud Barge On Order
|
|
2024 - Appx 8 Weeks to Completion
|
2024 Self Propelled Spud Barge
|
50'
|
|
|
50x12x4 Raked Bow Barge with following features: 1/4" Plate, 3x3x1/4" framing on 24" centers, 6 cleats, Flush manway, 2 coat epoxy paint system on exterior Internal spudwell 8" 6" sch80 steel spuds 20ft long with hats and pins Antifouling on underwater hull including 3rd coat of epoxy Bolt on plate anodes Aluminum console, dual engine brackets, rigging pipe chase 18" Structural crane pedestal and 6" elevated HPU platform Tiger 1069 Crane- 11,000lb max cap and 29ft max reach BravePro powerpack with 20 HP Honda Engine (2)Yamaha 115 XL shaft with all rigging and install (hydro steering, stainless props, batteries, controls, cables, harness, gauges, etc) Spud ring lifting collars
|
4. |
|
220' Deck Barge, Built in USA
|
|
1998
|
ABS Deck Barge
|
220'
|
|
|
This 220' Deck Barge was built to ABS A1 Standards in the USA. Has been sitting idle since off charter hire date 2020. Loadline classification expired April 2023. Barge needs repairs prior to reclassification as noted in survey. Survey available to end user-buyer only upon request.
|
5. |
|
40'x10'x4' Raked Bow Steel Barge
|
|
2024
|
Steel Sectional Barge
|
40'
|
|
|
40'x10'x4' Raked Bow Steel Barge: Standard features: 1/4" plate, 4 low profile cleats, 2 flush water-tight manways, transverse water-tight bulkhead, 3x3x1/4" angle framing on 20" spacing, impact protection outside angle cap on leading edge of headlog and rake as well as verticles on transom, 6" gussets on all 4 corners of each frame, 2 spudwells 8" diameter, 6x4x1/2" connecting rails, 1.25" conn pins Exterior epoxy paint system Accessory brackets on transomTerms: 50% down, balance on completion. Lead time- approx 4 weeks...subject to change!
|
6. |
|
2004 Inland Spud Barge For Sale 121
|
|
2004
|
Inland Spud Barge
|
124"
|
|
|
This Inland Spud Barge was US Built in 2004 with Coastwise Operational Endorsements in effect.
|
7. |
|
300' ABS/Loadline Deck Barge for Sale - 2000 Flag/Port of Registry : USA
|
|
2000
|
ABS Loadline Deck Barge
|
300'
|
|
|
This ABS Certified Deck Barge was Built in 2000 is a US Flagged Vessel/ : ABS / A1 GRT / NRT : 4058 / 1217 Length Overall : 300 feet (91.44 meters) Breadth : 100 feet ( 30.48 meters) Depth : 18 feet (5.48 meters) Max Draft : 14.0 feet (4.26 Meters) Approximate Light Ship Weight : 1544.6 LT (1569.3 Metric Tons) Approximate Cargo Capacity at Max Load Line : 9778.64 LT (9935.55 Metric Tons) Approximate Deck Loading : 3500 lbs/square foot (17 metric tons/square meter) Approximate Transverse Bulkhead : 7 Longitudinal Bulkhead : 3 No. of Compartments : 32
|
8. |
|
(2) 40' x 10' x 4' Sectional Spud Barges On Order
|
|
|
|
40'
|
|
|
Barge Details 2 – 10’ x 40’ x 4’ deep Sections are raked 38° one end with a 12” channel head log Three (3) compartments each section with three (3) flush mounted water tight hatches Four (4) - 18” welded kevels on each section A36 1/4” plate throughout. All seams welded inside and out below the deck plate Transverse frames on 2’ centers with 3”x3”x1/4” angle Longitudinal angles under deck on 18” centers: 3”x3”x1/4” angle Connecting angles of 6”x4”x5/8” angle on connected sides (1) with connecting pins on 4’ centers Two 12” x .500” wall thickness pipe spud wells on each section, 6” above deck Sections sandblasted on outside Deck coated with two..
|
9. |
|
USED 60' x 20' x 5' Spud Barge
|
|
2021
|
Spud Barge
|
60'
|
|
|
60' x 20' x 5' & 7' Dimensional selections Main Deck Plating = 3/8" Side Shell Plating = 5/16" Bottom Shell & Rake Bottom Plating = 5/16" Transom Plating = 5/16" 4x3x1/4” Angle Stiffeners on Hull Plates 3x2x1/4” Angle Stiffeners on Bulkheads Channel 10” Transverse Buck Frames as required Two 1/4” plate transverse watertight bulkheads Two 1/4" plate longitudinal bulkheads Six (6) dry void compartments (not for ballast) Radius corners for bilge and deck knuckles. 2 coats AF paint system for UW hull. Freeboard and rake are painted inorganic primer with two coats of navy blue. Deck is in organic primer with two..
|
10. |
|
ABS / A1 140' East Coast Spud Barge for Sale -144
|
|
2006
|
Spud Barge
|
140' 42.57 M
|
|
|
Transverse Bulkheads : (4) Longitudinal Bulkheads : (2) Compartments : 11 2000# / Sg.Ft. Deck Loading Estimated 10 Metric Tons/Square Meter This steel Spud Barge can easily be seen. Call or email Bob Carlson for a confidential appointment.
|
11. |
|
New 40'x12'x 4' Construction Barge for Sale- On Order
|
|
2023 Model
|
Spud Barge
|
40'
|
|
|
Just like new. This spud barge was recently built for owner that was too big for their project. Now must sell.
|
12. |
|
40' x 20' x 5' Hydraulic Spud Barge On Order
|
Custom Build
|
2022
|
Hydraulic Spud Barge
|
40'
|
|
|
Specifications 40' x 20' x 5' Hydraulic Spud Barge Main Deck Plating = 5/16" Side Shell Plating = 5/16" Bottom Shell & Rake Bottom Plating = 5/16" Transom Plating = 5/16" 5x3x1/4” Angle Stiffeners on Hull Plates 5x3x1/4” Angle Stiffeners on Bulkheads One (1), 1/4" plate transverse bulkhead Two (2) coats anti-corrosive marine epoxy and one (1) coat of anti-fouling on the underwater hull. Outfitting: Two (2) 18” manholes Two (2) hydraulic spuds Proposed Scheduling Barge Delivery: Four (4) months after receiving first batch of material to the shipyard. We will do all we can to cut this time. Proposed Payment Schedule 30% due at contract signing. 30% due at erection of bulkheads, shell..
|